Sending Images to a Smartphone (Wireless Connection) (EOS 6D Mark II)

    20-Oct-2020
    8203592700

    Solution

    Introduction
    You can save images from the camera to a smartphone using the following methods.
    ● Connecting via Bluetooth*
    When you connect the camera to a Bluetooth-compatible smartphone via Bluetooth, you can establish a Wi-Fi connection by operating only the camera or the smartphone.
    Note that pairing between the camera and smartphone is required to connect the camera to a smartphone via Bluetooth. Pairing will be done as part of the Bluetooth connection procedure.
    *This camera is Bluetooth 4.1 (Bluetooth low energy technology) compliant. To connect, your smartphone must be compatible with Bluetooth low energy technology.
    ● Connecting via NFC
    NFC-compatible smartphones can be connected via Wi-Fi by touching them to the camera.
    ● Connecting from the [Wi-Fi function] Menu
    You can use Wi-Fi to connect to a smartphone that is not compatible with Bluetooth or NFC or a smartphone that cannot use its Bluetooth or NFC function.
    IMPORTANT
    • Before connecting to the camera, you must install the free dedicated Camera Connect app on the smartphone.
    • Make sure that the smartphone's Wi-Fi function is on.

    Preparation: Installing Camera Connect on a Smartphone
    To connect the camera to a smartphone, the dedicated application Camera Connect (free of charge) must be installed on the smartphone.
    • Camera Connect can be installed from the Google Play or App Store.
    • When an NFC-compatible smartphone is touched to the camera before installing Camera Connect, the download screen of Camera Connect will be displayed on the smartphone.

    IMPORTANT
    • For the operating system versions supported by Camera Connect, refer to the "Related information" section below.
    • Interface or functions of the camera and Camera Connect are subject to change for firmware update of the camera or application update of Camera Connect, Android, iOS, etc. In such a case, features of the camera or Camera Connect may differ from sample screens or operation instructions in this manual.

    Step 1: Basic Camera Settings
    Configure necessary settings before using the wireless LAN functions of the camera.

    1. Set the camera's power switch to <ON>.

    2. Press the <MENU> button to display the menu screen.

    3. Press the <> button and display the < > tab.

    4. Select [Wireless communication settings] under the < > tab, then press < >.

    5. Select [Wi-Fi settings].

    6. Select [Wi-Fi].

    7. Select [Enable].

    8. When the screen below appears, press < >.

    9. Enter the nickname. You can enter any characters between 1 to 8 characters in length.
    When you finish entering characters, press the <MENU> button.
    * For more information on using the keyboard, refer to "Operation Reference: Virtual Keyboard Operation".
    NOTE
    When making Wi-Fi settings for the first time, a screen will appear for you to register a nickname for the camera (for identification).
    This nickname will be displayed on the screen of target devices when connecting to other devices via Wi-Fi. Be sure to set a nickname as otherwise you cannot go to the wireless LAN settings screen.

    10. When the screen below appears, select [OK], then press < >.
    To return to the [Wireless communication settings] screen, press the <MENU> button.

    11. The [Wireless communication settings] screen will appear.

    This concludes the explanation for basic camera settings.
     
    Depending on the connection method, choose one of the following and proceed to:
    • Step 2-A: Connecting via Bluetooth
    • Step 2-B: Connecting via NFC
    • Step 2-C: Connecting from the [Wi-Fi function] Menu

    Step 2-A: Connecting via Bluetooth
    IMPORTANT
    • This camera is Bluetooth 4.1 (Bluetooth low energy technology) compliant. To connect, your smartphone must be compatible with Bluetooth low energy technology.
    • Pairing is not possible while shooting with the camera.
    • The camera cannot be connected to two or more devices at the same time via Bluetooth.
    • Bluetooth connection consumes battery power even after the camera’s auto power off has activated. Therefore, the battery level may be low when you use the camera.

    2-A-1. Select [Bluetooth function].

    2-A-2. Select [Bluetooth function].

    2-A-3. Select [Smartphone].
    NOTE
    < > will be displayed on the camera’s LCD panel.

    2-A-4. Select [Pairing].

    2-A-5. Select [Do not display].

    Pairing will start.

    2-A-6. Enable the Bluetooth function on the settings screen of the smartphone, then start Camera Connect.



    2-A-7. Tap on the nickname of the camera to be paired.
    • iOS: When the screen below appears, tap on [Pair].

    2-A-8. Select [OK].
    : The device name set on Camera Connect

    2-A-9. Press < >.
    Pairing will complete and the camera will be connected to the smartphone via Bluetooth.

    Proceed to "Step 3-A: Sending Images to a Bluetooth-compatible Smartphone".

    Step 2-B: Connecting via NFC
    IMPORTANT
    • The camera cannot be connected to two or more smartphones at the same time.
    • When touching the smartphone to the camera, be careful not to drop the camera or smartphone.
    • Do not touch the smartphone to the camera with too much force. Doing so can scratch the camera or smartphone.
    • Just holding the smartphone close to the camera may not establish a connection. Be sure to touch the camera with the smartphone so that they come into contact with each other.
    • Recognition may be difficult depending on the smartphone. Touch slowly while changing the position or rotating horizontally. If connection is not established, keep the camera and smartphone together until the camera screen is updated.
    • Another application on the smartphone may start depending on how you touch. Check the position of the mark, then touch again.
    • When touching the smartphone to the camera, do not leave anything between the camera and smartphone. In addition, when a case is attached to the camera or smartphone, Wi-Fi connection with the NFC function may not be possible.
    • A Wi-Fi connection cannot be established with the NFC function between this camera and a smartphone while they are connected via Bluetooth.
    • To connect this camera to an NFC-compatible smartphone via Wi-Fi, the smartphone’s Wi-Fi and NFC functions must be enabled.
     
    NFC Function Cautions
    • A Wi-Fi connection cannot be established with the NFC function between this camera and another NFC-compatible device such as a camera or printer.
    • A Wi-Fi connection cannot be established with the NFC function while shooting with this camera, when there is no card, when the LCD monitor is closed with the screen facing inward, or while the camera is connected to another device with an interface cable.

    2-B-1. Enable the NFC function on the camera and smartphone.

    2-B-2. Touch a smartphone to the camera.
    • If an image is being played back on the camera, press the < > button to end the playback.
    • Touch the mark on the smartphone to that on the camera so that they come into contact with each other.
    IMPORTANT
    • Please check if your Android smartphone (OS version 4.0 or later) is compatible with NFC (Near Field Communication).
    • If your Camera Connect version is 2.7.10 or later, check the Android OS version of your smartphone. If the version is 10.0 or later, the camera firmware must be up to date to take advantage of NFC functionality. You can download the latest firmware from the Canon website.
    • Smartphones labeled with the mark are NFC-compatible.
    • Some smartphones are NFC-compatible even if they are not labeled with the mark. In such a case, check the NFC antenna position by referring to the smartphone’s instruction manual.
    • If you do not know whether your smartphone is NFC-compatible, contact the manufacturer of the smartphone.

    When a message indicating the connection is being established is displayed on the camera’s LCD monitor, move the smartphone away from the camera.
    Camera Connect starts on the smartphone and establishes a connection.

    2-B-3. When a connection is established, the screen below will appear on the camera’s LCD monitor.
    Select [OK] and press < >.
    : The device name set on Camera Connect

    2-B-4. A message indicating that the connection has been established is displayed and the [ Wi-Fi on] screen is displayed.
    NOTE
    If the camera screen switches during the smartphone operation procedures, press the <MENU> button to display the menu screen, then press the < > button to display the [ ] tab. Select [Wireless communication settings] under the [ ] tab, then select [Wi-Fi function] to return to the [ Wi-Fi on ] screen.

    Proceed to "Step 3-B: Viewing and Saving Images with a Smartphone".

    Step 2-C: Connecting from the [Wi-Fi function] Menu
    2-C-1. Select [Wi-Fi function].

    2-C-2. Select [ ] (Connect to smartphone).

    2-C-3. Select [Register a device for connection].

    2-C-4. Select [Do not display].

    2-C-5. Check the SSID and password.
    • Check the SSID (network name) ( ) and password ( ) displayed on the camera’s LCD monitor.
    • In [Wi-Fi settings], if you set [Password] to [None], the password will not be displayed or required.
    NOTE
    "_Canon0A" is displayed at the end of the SSID.

    2-C-6. Operate the smartphone to establish a Wi-Fi connection.
    • Activate the smartphone’s Wi-Fi function, then select the SSID (network name) checked in step 2-C-5 ( ).
    • For the password, enter the password checked in step 2-C-5 ( ).



    2-C-7. When the [Waiting to connect] screen is displayed on the camera’s LCD monitor, start Camera Connect on the smartphone.



    2-C-8. Select and tap on the camera to connect to via Wi-Fi from [Cameras] on Camera Connect.



    2-C-9. When a connection is established, the screen below will appear on the camera’s LCD monitor.
    Select [OK] and press < >.
    : The device name set on Camera Connect

    2-C-10. A message indicating that the connection has been established is displayed and the [ Wi-Fi on] screen is displayed.
    NOTE
    If the camera screen switches during the smartphone operation procedures, press the <MENU> button to display the menu screen, then press the < > button to display the [ ] tab. Select [Wireless communication settings] under the [ ] tab, then select [Wi-Fi function] to return to the [ Wi-Fi on] screen.

    Proceed to "Step 3-B: Viewing and Saving Images with a Smartphone".

    Step 3-A: Sending Images to a Bluetooth-compatible Smartphone
    3-A-1. Touch [Images on camera] in Camera Connect.
    • Android: When you select [Images on camera] in Camera Connect, a Wi-Fi connection will be automatically established.
    • iOS: On the smartphone’s Wi-Fi function screen, select the SSID (network name) and password displayed on the camera to establish a connection.



    3-A-2. The [ Wi-Fi on] screen will appear.
    NOTE
    If the camera screen switches during the smartphone operation procedures, press the <MENU> button to display the menu screen, then press the < > button to display the [ ] tab. Select [Wireless communication settings] under the [ ] tab, then select [Wi-Fi function] to return to the [Wi-Fi on] screen.

    3-A-3. Operate the smartphone to send images stored in the camera to the smartphone.
    When a list of images in the camera appears on the smartphone, tap [Select] on the upper right of screen.



    3-A-4. When the selection screen appears, choose the desired images ( ), then touch [Save] [ ] ( ). The selected images will be saved to the smartphone.



    3-A-5. After the images have been sent, tap on [ ] on the upper right, then touch [ ] on the upper left of the screen to return to the menu.







    3-A-6. To terminate the Wi-Fi connection, tap on [ ] on the upper right, then touch [YES].






    NOTE
    • To terminate the Wi-Fi connection, perform either of the following operations.
    - On the smartphone’s Camera Connect screen, tap on [ ].
    - On the camera’s [ Wi-Fi on] screen, select [Disconnect, exit].
    • Terminating the Wi-Fi connection will switch the camera to the Bluetooth connection.
    • You can check the connection status on the Camera Connect main screen:
    - Bluetooth connected
    - Wi-Fi connected

    IMPORTANT
    • With a Wi-Fi connection to a smartphone established, certain functions are unavailable.
    • In remote shooting, the AF speed may become slower.
    • Depending on the communication status, image display or shutter release may be delayed.
    • When saving images to a smartphone, you cannot take a picture even if you press the camera’s shutter button. Also, the camera’s LCD monitor may turn off.
    • Even if MOV-format movies are displayed in the list, they cannot be saved to a smartphone.
    NOTE
    • The Wi-Fi connection will be terminated if you set the camera’s power to <OFF> or open the card slot cover or battery compartment cover.
    • RAW images cannot be saved to a smartphone. When a RAW image is selected, it will be saved as a JPEG image.
    • With a Wi-Fi connection established, the camera’s auto power off does not function.
    • With a Wi-Fi connection established, disabling the smartphone’s power saving function is recommended.

    Step 3-B: Viewing and Saving Images with the Smartphone
    3-B-1. Touch [Images on camera] in Camera Connect.



    3-B-2. Use your smartphone to import images from the camera to the smartphone.
    When a list of the images on the camera appears on the smartphone, tap [Select] on the upper right of the screen.



    3-B-3. When the selection screen appears, choose the desired images ( ) and then touch [ ] ( ) on the bottom right of the screen. The selected images will be saved to the smartphone.



    3-B-4. After the images have been saved, touch [ ] on the top right, and then touch [ ] on the upper left of the screen to return to the menu screen.







    3-B-5. To end the connection, touch the [ ] icon on the upper right of the screen, and then tap [YES] when the confirmation screen appears.







    *Android™, and Google Play™ are trademarks of Google Inc.

    Operation Reference: Virtual Keyboard Operation
    For details on keyboard operation when registering camera’s nickname, refer to the following.
    You can change the nickname later on the [Wireless communication settings] screen.
    Changing the entry areaPress the < > button to toggle between the top and bottom entry areas.
    Moving the cursorPress the < > < > keys in the top area to move the cursor.
    Entering textIn the bottom area, press the < > < > or < > < > keys to select a character, then press < > to enter it.
    You can check how many characters you have entered and how many more can be entered by referring to [*/*] on the upper right of the screen.
    Changing the entry mode*Select [ ] at the bottom right of the bottom entry area. Each time you press < >, the entry mode will change as follows: Lower case -> Numerals / Symbols 1 -> Numerals / Symbols 2 -> Upper case.
    * When [Touch control: Disable] is set, you can enter all characters on one screen.
    Deleting a characterPress the < > button to delete one character.
    Finishing the text entryPress the < MENU > button to confirm what you have entered and exit. If a confirmation dialog is displayed, select [OK] to exit.
    Canceling the text entryPress the < INFO > button to cancel text entry and exit. If a confirmation dialog is displayed, select [OK] to exit.